Pre-heaters TERMOPRO

TERMOPRO® pre-heaters benefits:

  • 100% PCB deformation protection when heated
  • Best performance on the market and very even heat field
  • Extremely high heating transfer ability of working surface allows to change  temperature of the board rapidly and in result  to work out thermo profile
  • Ability to install a board directly on a table using PTFE racks without board sagging
  • Effective thermal insulation eliminates heating of unit case
  • Full antistatic protection prevents damage of electronic components
  • Connection  auxiliary temperature sens to PC for thermal profile control with automatic profiling
  • Wide size range: 64 mm to 340mm
  • 3-year manufacturer's warranty

 

Printed Circuit Board pre-heating in a process of installation or replacement electronic components has already became a routine procedure a long time ago. Bottom heating reduces a heat transfer from the component to the board, what in its turn reduces temperature at soldering instrument. Bottom pre-heating minimizes or even eliminates board warping caused by a difference in temperature across a board, and surface particularly, in a process of Hot-air and convection soldering technique of components replacement.

Special attention is paid to ceramic PCB’s due to the fact that these materials require smooth and slow pre-heating before soldering, because of its sensitivity to rapid temperature changes.

A plate - a heater in preheating devices TERMOPRO®, can be either in direct contact with a board, or PCB held by a frame of board holder with a gap over plate. The special design of heating elements and a plate provide high uniformity of a temperature across working surface. Selecting a model of pre-heater it is important to ensure that the size of the heater is larger than the size of the PCB. Heating will be the most even and board warping will be minimal in this case.

Pre-heaters are available with working area in a range from 65mm to 340mm, depending on the model. It provides uniform heating even along very large boards. Temperature control is managed by auxiliary digital PID-thermostat (controller). The thermostat can measure temperature of a plate or PCB by the external sensor depending on controller model. “PRO” index controller series can be connected to a computer for work with thermo profile. Profiles are clearly displayed on PC through friendly interface.

Case design prevents overheating and ensures operator safety. All devices are equipped with protective ground and are ESD-tested.

 

NP-series
Pre-heaters with external controller

 

For complex tasks, where a heating process requires precision temperature control, BGA soldering, heating PCBs with radiators or perform thermal profile TERMOPRO® has developed a professional NP series.

 

Preheat and soldering with Thermo profile

This function provides a link with a sensor on PCB. The system uses a "TERMOPRO CENTER" software which automatically adjusts temperature on a board supporting a desired thermal profiles. Optional air cooler FC-500 can automatically generate cooling zone in thermal profile when required.

 

Homogenous heating

Uniform distribution of the temperature field across working surface is achieved by a special design of the heating elements mounted in an aluminum plate with a heat resistant coating.

 

Quality and reliability

NP series are designed for industrial applications. Robust steel casing, good thermal insulation, control unit in separate case, stable specification - all these demonstrate the reliability of products that developed and manufactured  for long-term operation in industrial environment.

 

Features and applications: 

  • Can be incorporated into infrared BGA rework soldering station IK-650 PRO
  • Soldering SMD-components with thermo profile
  • Pre-heating PCB before soldering SMD
  • Pre-heating of PCB for repair
  • Pre-heating boards with radiators installed
  • Pre-heating of ceramic components before soldering
  •  BGA re-balling
  • Thermo-bond adhesive (chip-bonder)
  • PCB utilization
  • Silicon plates preheating

 

 

Technical specification

NP 34-24  PRO

NP 24-17 PRO

NP 17-12 PRO

NP 10-6 PRO*

NP 6-5 PRO*

Input [V]

~230

~230

~230

~230

~230

Heating power [Watt]

2800 (2 х 1400)

1400

700

350

175

Power density[Watt per m2]

34300

34300

34300

51200

48900

Temperature range [°С]

50 – 350

50 – 350

50 – 350

50 – 350

50 – 350

Temperature accuracy [°С]

± 2

± 2

± 2

± 2

± 2

Dimensions of the heating plate [mm]

340х240
(2plates 240х170)

240 х 170

170 х 120

105 х 65

65 х 50

IR range [um]

2-10

2-10

2-10

2-10

2-10

Size [mm]

420х300х50

300х250х50

250х175х50

190х130х50

135х130х43

Weight [kg]

5,5

3,2

1,3

1,2

0,6

Usable external temperature controller

TP 2-10 АB PRO/
TP 2-10 KD PRO

TP 1-10 KD PRO,TP 1-10 KD

TP 1-10 KD PRO,TP 1-10 KD

TP 1-10 KD PRO,TP 1-10 KD

TP 1-10 KD PRO,TP 1-10 KD

Homogenous heating

+

+

+

+

+

 

 

 

TP-series

External controllers

 

(TP2-10 AB PRO version presented)

 

TP 1-10 KD PRO

This one-channel temperature controller is designed to control temperature of pre-heaters TERMOPRO® NP-series with single heating plate (excluding NP24-34). A controller is equipped with an additional temperature sensor to check temperature on a board. A controller allows boards soldering and heating by thermo profile. This function is provided by link with a sensor on a board. The controller adjusts operation of a heater automatically to match desired thermo profile while running the program "TERMOPRO CENTER" software. A heating thermo profile curve is displayed at  Operator PC monitor.

 

TP 1-10

This one-channel temperature controller is designed to control temperature of pre-heaters TERMOPRO® NP with one heating plate (excluding NP24-34) without thermal profiling.

 

TP 1-10 KD

This one-channel temperature controller is designed to regulate temperature of preheaters TERMOPRO® NP with one heating plate (excluding NP24-34 without thermal profiling. The controller is equipped with an additional temperature sensor to check the temperature on a board.

 

TP 2-10 АB PRO

 

The two-channel temperature controller is designed to regulate temperature of NP 34-24 preheater with two independent working plates or two NP 24-17 with single plate. Controller enables a heating process with thermal profiles working in a set with soldering station IK-PRO 650. A controller can operate with "TERMOPRO CENTER" software in the same way as controller TP 1-10 KD.

  

Technical specification

Input

230VAC / 50Hz

Channels

1 Channel (TP 1х, IK 1х) or 2 Channels (TP 2х, IK 2х)

Maximum load

2000Watt per channel

Temperature range

50 - 350°C (IK х 50 - 400°C or 50 - 650°C)

Temperature accuracy

±1°C (depends on the type of load)

Temperature step

1°C

Memory for temperatures

6 cells per channel

Thermo profiling

Available in models with index "PRO"

External temperature sensor

Available in models with index "KD"

External sensor temperature range

-70 to +500°C

External temperature sensor size

4 х 2 х 0.5 mm

Temperature measuring speed

15 times per second in each channel

Temperature controller weight

1,6 to 1.9 kg (depends of model)

 

 

 

 

Part No.

Description

 

 

 NP3424TP2AB-Pro

PCB Preheating System  NP34-24 with PC interface

 

 NP3424TP2KD-Pro

PCB Preheating System  NP34-24 with PC interface and sensor

 

 

 NP2417TP1KD-Pro

PCB Preheating System  NP24-17 with PC interface and sensor

 

 NP2417TP1KD

PCB Preheating System  NP24-17 with sensor

 

 NP2417TP1-10

PCB Preheating System  NP24-17

 

 

 NP1712TP1KD-Pro

PCB Preheating System  NP17-12 with PC interface and sensor

 

 NP1712TP1KD

PCB Preheating System  NP17-12 with sensor

 

 NP1712TP1-10

PCB Preheating System  NP17-12

 

 

 NP106TP1KD-Pro

PCB Preheating System  NP10-6 with PC interface and sensor

 

 NP106TP1KD

PCB Preheating System  NP10-6 with sensor

 

 NP106TP1-10

PCB Preheating System  NP10-6

 

 

 NP65TP1KD-Pro

PCB Preheating System  NP6-5 with PC interface and sensor

 

 NP65TP1KD

PCB Preheating System  NP6-5 with sensor

 

 NP65TP1-10

PCB Preheating System  NP6-5

 

 

 RD-400Н

Frame board holder 400mm

 

 

 FSK-15

PTFE rack 10 pack

 

 

 FSM-15

PTFE rack 10 pack

 

 

 FC-500

Air PCB cooler

 

 

 TA-570M

Temperature measuring unit, 3 channel, PC interface, with thermo sensors

 

 

 TD-1000/1.5
 TD-1000/2.2

Thermo sensor TD-1000 4x2x0.8mm 1.5m cable
Thermo sensor TD-1000 4x2x0.8mm 2.2 m cable

 

 

 

 PDS-300

Joint clamp with temperature sensor

 

 

 PK-40, PK-50, PK-60

3D IR concentrators (Patented), 3 pieces